QuickPipe is dedicated for the calculation on fluid properties such as temperature, energy change, heat transfer, pressure loss and etc for pipes/tubes/hoses. The database consists of more than 50 different fluids, more than 200 different metal tubes/pipes and more than 200 different plastic pipes. With such database of wide coverage, QuickPipe can help engineers perform following calculations with ease.
1. Obtain the amount of heat transfer (aka energy change) based on temperature differences. (Alternative control parameters including both mass and volume of fluid.)
2. Obtain the heat transfer rate based on temperature differences. (Alternative control parameters including both mass and volume flow rates of fluid.)
3. Determine temperature differences from the amount of heat transfer in a closed system.
4. Determine temperature differences from the heat transfer rate in a dynamic system.
5. Check the nominal sizes, DN, outside diameter, internal roughness and weight per ft of various tubes/pipes.
6. Obtain the unit pressure loss of each pipe/tube/hose selected based from the values of the current flow rate and pipe/tube/hose length input by users.
7. Calculate the overall pressure loss based on the pipe/tube/hose length along with the numbers of 90° Ells, 45° Ells, side branch of Tee, straight run of tee, couplings, ball valves, gate valves, butterfly valves and check valves.
8. A complete unit database allows the user to select the most familiar units of energy, heatload, pressure, length, flow rates and etc.
9. An user-friendly interface to allow the change on the settings of the pressure Loss in Fittings and Valves expressed as equivalent length of tube/pipe/hose.
流体工具箱是特別针对流体相关设计人员, 维护管理及操作人员的需求, 而设计之快速计算工具。可以立即计算吸放热与温度变化,传热量与温度变化,管路单位压损值及管路总压损。资料库内内建有超过50种不同的流体,超过两百种不同的金属管以及超过两百种不同的塑胶管。使用者可以利用如此详细的资料库来进行以下的快速运算:
1. 固定系统由输入的初始温度及最终温度求得总吸放热。(可输入流体质量或是流体体积)
2. 流动系统由输入的初始温度及最终温度求得总吸放热量。(可输入质量流量或是体积流量)
3. 由总吸放热回推固定系统的温度差。
4. 由总吸放热量回推开放流动系统的温度差。
5. 快速查询数百种金属管及塑胶管之标称直径,DN值,外径,管壁厚度,内部表面粗糙度,每英呎重量等数据。
6. 由使用者输入的体积流量及管路长度来计算目前选用的金属管及塑胶管之单位压损。
7. 由使用者输入的管路本身长度及目前流量,标準90°弯头个数,标準45°弯头个数,90°三通(侧向)个数,45°三通(直向)个数,连接头个数,以及各式阀门如球阀,闸阀,蝶阀及止回阀之个数等等,直接求得预估管路总压损。
8. 完整的单位资料库方便使用者直接设定最熟悉的温度,质量,体积,质量流量,体积流量等单位。
9. 方便而快速的使用者介面可以直接设定接头及阀门的等效管路长度,标準90°弯头,标準45°弯头,90°三通(侧向),45°三通(直向),连接头,以及各式阀门如球阀,闸阀,蝶阀及止回阀等元件在不同尺寸下等同于多少长度之管路,作为预估管路总压损之基準。